Gazebo Seoul avec toit en Acier Galvanisé, 10'x14'

N° d'article 330666498 N° de modèle B101424-FNE-POL
Gazebo Seoul avec toit en Acier Galvanisé, 10'x14'
 

Caractéristiques

Profitez de votre Gazebo Séoul 10'x14' pour les journées ensoleillées, pluvieuses ou venteuses. Ce cadre durable en acier e-coat et aluminium et toit en acier galvanisé sont conçu pour apporter style et utilité à votre cour arrière. La finition en poudre de couleur marbre bronze résiste à la corrosion et a fière allure dans chaque patio ou jardin. Deux rails permettent d'installer des moustiquaires en polyester (inclus), des rideaux ou des micas vendus séparément. Ce gazebo est disponible en différentes grandeurs: 10'x10 'et 10'x12'.

  • 4 saisons
  • Disponible dans 3 grandeurs 10'x10', 10'x12' et 10'x14'
  • Cadre en aluminium et en acier e-coated qui a une protection contre la rouille, vis en stainless, toit en Acier Galvanisé
  • Système à 2 rails pour la moustiquaire et les rideaux
  • Moustiquaire en mailles de polyester
  • Un poteau hivernal peut être installé pour ajouter encore plus de support à votre gazebo pendant la saison hivernale et une toile hivernale pour faciliter le glissement de la neige.
  • Quatre trous d'ancrage à la base de chaque poteau pour fixer le gazebo plus solidement au sol. Quincaillerie d'ancrage non comprise
  • Assemblage requis d'une durée approximative de 6 heures à 2 personnes

Spécifications techniques

Bancs inclus :Non Nom de la collection :Gazebo Plancher inclus :Non Composition du toit :Acier Garantie :1 an Couleur/fini du fabricant :Neutre Type :Permanent Matériau du cadre :Aluminium Type de métal :Acier inoxydable Peut être peint :Non Matériau principal :Acier Couleur/fini du mobilier de patio :Havane Bardeaux inclus :Non Forme :Rectangle Moustiquaire inclus :Oui Profondeur extérieure (pi) :14 Hauteur extérieure (pi) :8,8 Largeur extérieure (pi) :10 Hauteur intérieure (pi) :8,8 Longueur de la fondation (pi) :12 Largeur de la fondation (pi) :10

Vous pourriez aussi aimer

TOJA GRID
Supports de coin pour pergolas Toja Grid, paquet de 2
Format 4x4"-2PK
N° d'article 46625006
N° de modèle G021030MB1
★★★★★ ★★★★★
3
(2)
TOJA GRID
Trousse de pergola Toja Grid avec voile d'ombrage pour pôteau de bois 6x6, 10 pi x 12 pi, autoportant
N° d'article 330765478
N° de modèle SA61012GR13
★★★★★ ★★★★★
0
(0)
TOJA GRID
Pied de poteau pergola Toja Grid, acier, 4" x 4", lot de 4
Format 4x4"-4PK
N° d'article 46625007
N° de modèle G021012MB1
★★★★★ ★★★★★
4,4
(8)
TOJA GRID
Trousse de pergola double Toja Grid avec 2 voiles d'ombrage pour pôteau de bois 6x6, 8 pi x 22 pi, autoportant
N° d'article 330765497
N° de modèle DP60822GR13
★★★★★ ★★★★★
0
(0)
TOJA GRID
Trousse de pergola double support mural Toja Grid avec 2 voiles d'ombrage, 10 pi x 20 pi
N° d'article 330765498
N° de modèle DS61020GR13
★★★★★ ★★★★★
0
(0)
TOJA GRID
Trousse de pergola Toja Grid avec voile d'ombrage pour pôteau de bois 6x6, 8 pi x 10 pi, autoportant
N° d'article 330765499
N° de modèle SA60810GR13
★★★★★ ★★★★★
0
(0)
TOJA GRID
Trousse de pergola double support mural avec 2 voiles d'ombrage Toja Grid, 8 pi x 20 pi
N° d'article 330765473
N° de modèle DS60820GR13
★★★★★ ★★★★★
0
(0)
TOJA GRID
Trousse de pergola support mural Toja Grid avec voile d'ombrage pour pôteau de bois 6x6, 10 pi x 12 pi
N° d'article 330765500
N° de modèle SS61012GR13
★★★★★ ★★★★★
0
(0)
TOJA GRID
Base de poteau et support de montage mural pour pergola Solo de Toja Grid
N° d'article 330765463
N° de modèle G031071MB1
★★★★★ ★★★★★
0
(0)
TOJA GRID
Trousse de pergola double support mural Toja Grid avec 2 voiles d'ombrage, 8 pi x 22 pi
N° d'article 330765474
N° de modèle DS60822GR13
★★★★★ ★★★★★
0
(0)
TOJA GRID
Poteau à bois Toja Grid, table carré, acier 4 po x 4 po, noir
Format 4x4
N° d'article 46625020
N° de modèle G0112STMB1
★★★★★ ★★★★★
0
(0)
TOJA GRID
Trousse de pergola support mural Toja Grid avec voile d'ombrage pour pôteau de bois 6x6, 8 pi x 10 pi
N° d'article 330765505
N° de modèle SS60810GR13
★★★★★ ★★★★★
0
(0)
TOJA GRID
Ensemble de supports Quad pour pergolas Toja Grid
Format 4x4"-2PK
N° d'article 46625008
N° de modèle G021040MB1
★★★★★ ★★★★★
4
(1)
TOJA GRID
Trousse de pergola mural avec poteau Knect de Toja Grid 6x6 et voile d'ombrage, 8 pi x 10 pi
N° d'article 330765470
N° de modèle PW60810GR13
★★★★★ ★★★★★
0
(0)
TOJA GRID
Trousse de pergola Toja Grid avec voile d'ombrage pour pôteau de bois 6x6, 8 pi x 12 pi, autoportant
N° d'article 330765501
N° de modèle SA60812GR13
★★★★★ ★★★★★
0
(0)
TOJA GRID
Trousse de pergola support mural Toja Grid avec voile d'ombrage pour pôteau de bois 6x6, 8 pi x 12 pi
N° d'article 330765486
N° de modèle SS60812GR13
★★★★★ ★★★★★
0
(0)
TOJA GRID
Support d'extension de pergola à 4 bras Quad de Toja Grid, autoportant
N° d'article 330765518
N° de modèle G031041MB1
★★★★★ ★★★★★
0
(0)
TOJA GRID
Trousse de pergola Toja Grid avec voile d'ombrage pour pôteau de bois 6x6, 8 pi x 8 pi, autoportant
N° d'article 330765490
N° de modèle SA60808GR13
★★★★★ ★★★★★
0
(0)
TOJA GRID
Trousse de pergola support mural Toja Grid avec voile d'ombrage pour pôteau de bois 6x6, 12 pi x 12 pi
N° d'article 330765464
N° de modèle SS61212GR13
★★★★★ ★★★★★
0
(0)
TOJA GRID
Trousse de hamac Toja Grid pour 2 personnes pour du bois 6x6, 8 pi x 8 pi, autoportant
N° d'article 330765475
N° de modèle HMK6W1GR1S
★★★★★ ★★★★★
0
(0)
TOJA GRID
Braquette de base pour pergolas Toja Grid, noir mat, 4/pqt
Format 6x6"-4PK
N° d'article 46625017
N° de modèle G031014MB1
★★★★★ ★★★★★
0
(0)
TOJA GRID
Support de genou à 45 degrés pour poteaux en bois 4 pi x 4 pi - paquet de 2 noir
Format 4x4
N° d'article 46625022
N° de modèle G01454MB1
★★★★★ ★★★★★
0
(0)
TOJA GRID
Toile pour pergolas Toja Grid, 10' x 10', graphite
Format 10x10"
N° d'article 46625002
N° de modèle G131010GR1
★★★★★ ★★★★★
0
(0)
TOJA GRID
Trousse de pergola double Toja Grid avec 2 voiles d'ombrage pour pôteau de bois 6x6, 12 pi x 20 pi, autoportant
N° d'article 330765495
N° de modèle DP61220GR13
★★★★★ ★★★★★
0
(0)
TOJA GRID
Trousse de pergola double support mural Toja Grid avec 2 voiles d'ombrage, 10 pi x 22 pi
N° d'article 330765471
N° de modèle DS61022GR13
★★★★★ ★★★★★
0
(0)

how many boxes does it ship in?

Posée par: lowes3062
  • y_2021, m_3, d_3, h_8CST
  • bvseo_bulk, prod_bvqa, vn_bulk_3.0.14
  • cp_1, bvpage1
  • co_hasquestions, tq_1
  • loc_fr_CA, sid_330666498, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_renodepot
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • LOCAL, getContent, 1ms
  • QUESTIONS, PRODUCT
Gazebo Seoul avec toit en Acier Galvanisé, 10'x14' est évalué 5.0 de 5 de 1.
Rated 5 de 5 de par A challenge to assemble but worth it. 10 x 14 Seoul Gazebo So! This gazebo looks great now that it is assembled. The instructions state that 2 people can assemble this in 6 hours and it is better with 4 people. I think that 4 is too many. Only certain things can be done at any one time. Here is my experience with this process. First, the gazebo comes in two HEAVY boxes. The boxes just showed up in my driveway and I did not even know that they had been delivered. No knock on the door, no doorbell, nothing. This is a delivery company issue but if I had been made aware, I would have asked to have the boxes dropped at the back of the driveway and not in the middle of the driveway (blocking any vehicles from leaving also!). The main box weighs 74KG or about 160lbs. I had to open the box and transport all the components to the deck individually. The second box was not as heavy but is all sheet metal so it flexed and could not be carried so had to put it onto a wheelbarrow to move it. All frame components have a lettered sticker on them and are enclosed in a clear plastic bag. The tools, bolts, guidebook and touch up paint come in a smaller box. There is also a bag of extra bolts. I suggest that you take your time and familiarize yourself with the guidebook before taking on this assembly. The sheet metal roof has material between each piece to prevent scratches. Use gloves and be careful! The edges are sharp and some corners are very pointy. The package also comes with two adjustable poles to support the longer, horizontal span when there is snow on it. Great idea! Preparation: You will benefit from having a taller ladder, (6-10’), a bench or similar to stand on, a 20’ measuring tape and a c-clamp or c-vice grips. Gloves when handling the roof is also suggested. And patience. Lots of patience. Assembly: I assembled this with a friend who is mechanically inclined, as am I. It helped that we were both like-minded in our methods. The booklets/instructions (English & French) are typical line diagrams and provide basic directions. The most important point is to NOT tighten the bolts until all components of a section are assembled. In fact, during assembly of the roof, we did not tighten any components until completed. The exception to this were the topmost screws of the roof panels. See Roof section. Expanding on this concept, do not OVER tighten. Some of the threads are just cut into sheet metal and it would easy to strip these threads. The riv-nuts are more robust so you can apply more torque but be aware that the threads can be stripped relatively easily. This gazebo was assembled on a deck so being level was not an issue. If you are doing this on ground, ensure that your posts are level. Things will just go easier. I mean, less difficult. The very first issue came with connecting the base plates to the bottom of the posts. The instructions state to insert three bolts through three holes in the post, and into the plate. There are only two holes. I was not going to pack everything up and send it back to Lowe’s for that, so I carefully drilled a hole, put a bolt in and …..the base plate is not threaded! I am not sure if this is a quality control issue or not but this is poor design. The base plate should have all three bolts attached. Moving on. The longer and shorter horizontal members assembled easily. We assembled the horizontal members to the posts on the ground, then stood the assembly up. The only time an extra hand would have been beneficial was during this step. Diagonal braces went on without issue. Once the four horizontal members are bolted onto the four posts, carefully measure the diagonal and adjust before tightening the braces and moving on. For the next step, you will need a hover-board from Back to the Future. Seriously. OK, the instructions do not say how to do the roof trusses so this is what we did. The heavier K pieces were attached to the corners. (They will self support for the amount of time needed) Then my friend stood on the ladder and held the bottom roof plate in place while I stood on the bench and attached the corner members to the roof plate. The remaining L pieces all attached easily. Do NOT tighten these as adjustments will be made until the very end. Lateral cross members are installed now. Again do not over tighten. The top roof plate went on next. Leave this very loose. Looking back, we both agreed that this heavy component could have been left off completely until the just before the last roof panel was put on. The issues that we had with trying to wedge the roof panels between the top and bottom roof plates could all have been avoided by simply not having that plate on until much later in the process. The hook goes into the bottom plate. I actually used the hook to pull down on the bottom plate to allow more room to install roof panels at the top. If you made it to this stage in a few hours and are feeling confident, that is about to be shattered. We assembled the frame in less than 2 hours. The remaining time was spent on the roof panels. Here are some points to ponder from our experience. You may need to leave the top and bottom roof plate Very loose in order to slide panels between them. Again, consider leaving it off entirely until the end. The catch here is that you need to tighten it before putting the last few panels in place. If you do not, you will not be able to tighten it once all the panels are in place. The manual says to install panel Y first. This is fine for the first side but as we progressed, the order was less important. In fact we put Y in last on the last side in order to be able to tighten the top cap. The roof is where the concept of not tightening the frame bolts comes into play. As panels were slid into place, the holes would not always align. However, being that the trusses were loose, it was easy to align the holes in the roof panels with the mounting points on the frames. NOTE! When you tighten a roof panel, it will easily deform the plate and cause a buckle to either side of where you tightened it. This works to your advantage for the triangular corner pieces but against you on the main panels. The buckling will also provide an entrance for mosquitoes. Again, do not tighten any roof panel bolts until all are in place. You need to be aware of tightening the upper row of bolts on the roof before putting all the panels in. The lower row of bolts can be tightened from the ladder. We were frustrated at the wide gap between the corner K supports and the triangular roof panels but as the roof and frames were tightened, the gaps closed up and had a surprisingly good fit. Once the roof panels were tightened, we tightened the trusses from under the roof. We also attached the edge/trim/drainage channels. I am not sure how these will work. The design seems to be to channel the water to the corners and drain from there. I contacted Corriveau for 6 extra CC bolts and nuts. The instructions say to use BB bolts to attach the edge/trim. These bolts are fine for the centers of the trim but at the joints, there is an additional gusset welded onto the ends to allow the two to be bolted together. This additional thickness makes it impossible to use a BB bolt with an HH plastic washer. Remember the clamp/C-vice grip from above? We used that to squeeze the gusset together in order to BARELY get a BB nut and bolt to thread together without a washer. Screens went up quickly with each piece being half of a short side and half of a long side and a ribbon sewn at the junction to tie the screen to the post. In total, assembly time took 8-9 hours. The majority of time was spent adding and removing roof panels. We are both of the opinion that this process could have been a lot easier without the top plate until the end. Actual dimension of the roof is just over the 10’ x 14’ advertised size. There have been several good rains and it does not leak. I think that the plastic washers on the roof will start to fail over time due to UV but time will tell. There are some rubber edge gaskets that work well at the points where there is roof panel to horizontal member contact, but mosquitoes will easily get in through the ribs. I will probably plug the gaps with plugs of circular foam. All in all, it is a nice gazebo. Deck furniture fits nicely under it and the net pulls into place smoothly and the zippers seem robust. Curtains do not come with this kit and at present, we are still not able to find the correct ones for this gazebo. I cannot give it 5 stars due to things like the missing holes in the base-plate and other issues that were encountered. Service from Corriveau was excellent. If this review allows me to update it, I will let you know how it survives the winter snow.
Date de publication: 2020-06-03
  • y_2021, m_3, d_3, h_8
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.14
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_1
  • loc_fr_CA, sid_330666498, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_renodepot
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • LOCAL, getContent, 8ms
  • REVIEWS, PRODUCT

Changement de magasin

Vous êtes sur le point de changer de magasin.

Veuillez noter que si vous changer de magasin, les prix affichés sur le site Web peuvent changer et votre panier d'achats pourrait alors se vider.

Conserver mon magasin Changer de magasin