Peinture imperméabilisante/anti-moisissure, Zinsser, huile, 3,7 l, blanc

N° d'article 03305746 N° de modèle Z05011 Format3.7L
Peinture imperméabilisante/anti-moisissure, Zinsser, huile, 3,7 l, blanc
 

Caractéristiques

Peinture pour sous-sols et maçonnerie. Anti-moisissure. Imperméabilité garantie à vie. Résiste à une pression jusqu'à 34 PSI. Fini lisse, non granuleux, facile à appliquer sur des murs secs ou humides. Formule à base d'huile à faible odeur. Blanc. 3.7 L

Spécifications techniques

Utilisations :Sous-sols et maçonnerie Format :3,7 l

Vous pourriez aussi aimer

ZINSSER
Apprêt d'impression antitache Cover Stain(MD), 946 ml, blanc
Format 946ML
N° d'article 03305623
N° de modèle 256185
★★★★★ ★★★★★
0
(0)
SICO
Apprêt-scelleur Go Prime(MD) Sico(MD), 946 ml, blanc
Format 946ML
N° d'article 50316649
N° de modèle 150-135-946ML
★★★★★ ★★★★★
3
(1)
SICO
Apprêt-scelleur Sico GoPrime, latex alkyde, 3,78 l, blanc
Format 3.78LT
N° d'article 50316648
N° de modèle 150-135-3.78L
★★★★★ ★★★★★
3
(1)
ZINSSER
Apprêt d'impression antitache Cover Stain(MD), 3,78 l, blanc
Format 3.78LT
N° d'article 03305624
N° de modèle 256184
★★★★★ ★★★★★
0
(0)
ZINSSER
Apprêt bloque-taches Zinsser, B-I-N 2(MD), 3,78 l, blanc
Format 3.78L
N° d'article 03305742
N° de modèle 261664
★★★★★ ★★★★★
0
(0)
KILZ
Apprêt-scellant intérieur Kilz Original, alkyde, 18,93 l, blanc
Format 18.93LT
N° d'article 08405324
N° de modèle 10030C
★★★★★ ★★★★★
3,7
(3)
ZINSSER
Apprêt bloque-taches Zinsser, B-I-N 2(MD), 946 ml, blanc
Format 946ML
N° d'article 03305743
N° de modèle 261663
★★★★★ ★★★★★
0
(0)
ZINSSER
Apprêt antitache, Zinsser, 18,9 L, blanc
Format 18.9LT
N° d'article 03305622
N° de modèle 256188
★★★★★ ★★★★★
4
(1)
SOLIGNUM
Peinture alkyde de signalisation Solignum, 18,9 l, blanc
Format 18.9L
N° d'article 31035079
N° de modèle 12413-20-SOL
★★★★★ ★★★★★
0
(0)
SOLIGNUM
Peinture de signalisation Solignum, 3,78 l, jaune
Format 3.78L
N° d'article 31035080
N° de modèle 12513-4-SOL
★★★★★ ★★★★★
0
(0)
SOLIGNUM
Peinture de signalisation Solignum, 3,78 l, bleu
Format 3.78L
N° d'article 31035076
N° de modèle 12713-4-SOL
★★★★★ ★★★★★
0
(0)
SOLIGNUM
Peinture alkyde de signalisation Solignum, 3,78 l, noire
Format 3.78L
N° d'article 31035077
N° de modèle 12113-4-SOL
★★★★★ ★★★★★
0
(0)
SOLIGNUM
Peinture de signalisation Solignum, 3,78 l, blanc
Format 3.78L
N° d'article 31035078
N° de modèle 12413-4-SOL
★★★★★ ★★★★★
0
(0)

after cureing does it give off any V.O.C's? Would it be safe to use around animals??

Posée par: Dave Kyle
The spec sheet says: "53% of the mixture consists of ingredient(s) of unknown acute toxicity." and "The acute effects of this product have not been tested." This means that Rust-Oleum is saying they DO NOT KNOW what the effects will be --- CURED OR NOT!!! Here are some details direct from the spec sheet. They should make you understand that CLEARLY when the respresentative from Rust-Oleum answered, "Once cured, it doesn't give off any VOCs and is non toxic", you are being misinformed. Source: https://www.rustoleum.com/MSDS/ENGLISH/5001.pdf Available from: https://www.rustoleum.com/product-catalog/consumer-brands/zinsser/waterproofing-paints-and-sundries/watertite-mold-and-mildew-proof-waterproofing-paint/
Répondue par: sourceagent
Date de publication: 2021-01-30

What are the application and prep instructions on a floor

Posée par: Beme
Hi Beme, Surfaces must be clean, dry, sound and free of dirt, greases, soap, and other contaminants. Salting or efflorescence, mould and mildew must be removed. Our WaterTite Waterproofing paint can be used over previously painted, non-glossy surfaces; however its waterproofing ability is then dependent upon the integrity of the previous coating. For best results, remove as much of the old coating as possible by manually scraping the surface, followed by thorough wire rushing. Exterior surfaces should be power washed or abrasive blasted to remove all loose and scaling paint and cement. All holes and cracks, especially active water leaks, must be patched with WaterTite Polyurethane Sealant or a similar product. Follow manufacturer’s directions for dry time, etc. Use in a well ventilated area. Extinguish all pilot lights and other sources of flames or ignition. Remove electrical equipment from the area. Stir or mix thoroughly before and during application. DO NOT THIN. Apply only when air, material, and surface temperatures are between 10-32ºC (50-90ºF) and the relative humidity is or less than 85%. Liberally apply the first coat using a thick polyester bristle brush, or by rolling a small section (91 cm x 91 cm (3x3 foot)) and then using a brush to work the coating into the pores of the masonry. Apply as much paint as necessary to produce a continuous, pinhole free film. Use a 25 mm (1”) nap roller cover for unpainted, porous surfaces or a 20 mm (¾”) nap roller cover for smooth or previously painted surfaces. The second coat can be brushed or rolled.
Répondue par: Rust-Oleum Answers
Date de publication: 2020-08-12

Would this work on a slate shower

Posée par: Donnyp
Hi Donnyp, Our WaterTite Waterproofing paint is for concrete and masonry surfaces only.
Répondue par: Rust-Oleum Answers
Date de publication: 2020-08-12

Does it work on tiled surface? I mean does it adhere to tile? Can I apply thinset mortar on top of it to install second layer of tile over it (on shower floor and wall)?

Posée par: pezz
Hi Pezz, Our WaterTite is for concrete and masonry surfaces only and we do not recommend it for tile.
Répondue par: Rust-Oleum Answers
Date de publication: 2020-08-12

Would this paint work on the inside of my 50 year old concrete laundry tub?

Posée par: debbie81
This paint is made for concrete only
Répondue par: Rust-Oleum Answers
Date de publication: 2020-08-07

I will be waterproofing a basement concrete wall and then glueing foam slab insulation to the concrete wall with PL300. How well does this Watertite product accept the PL300 adhesive? Will it peel off and result in loss of the foam slab insulation?

Posée par: JWMT
Hi JWMT, Thank you for your question. Either Watertite product should be fine with your adhesive. We recommend testing the paint on a stir stick first. Allow for full cure, which is 7-14 days, depending on temperature and humidity. Once cured, apply your PL300 adhesive to the stick and see if it dries and sticks. If your test is successfully then you should feel confident that the adhesive will stick to the painted concrete. We hope this answers your question. Feel free to contact us again if you require further information.
Répondue par: Rust-Oleum Answers
Date de publication: 2019-05-28

Can this product be used on a plywood subfloor material to add waterproof protection?

Posée par: DMK55
The Zinsser WaterTite is to be used on concrete only
Répondue par: Rust-Oleum Answers
Date de publication: 2019-04-30

Is this paint tintable to a dark colour?

Posée par: Fay23
This paint cannot be tinted to a dark color
Répondue par: Rust-Oleum Answers
Date de publication: 2019-03-12
  • y_2021, m_4, d_11, h_16CST
  • bvseo_bulk, prod_bvqa, vn_bulk_3.0.14
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_17
  • loc_fr_CA, sid_03305746, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_renodepot
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • LOCAL, getContent, 1ms
  • QUESTIONS, PRODUCT
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • LOCAL, getContent, 0ms
  • REVIEWS, PRODUCT
  • bvseo-msg: The resource to the URL or file is currently unavailable.;

Changement de magasin

Vous êtes sur le point de changer de magasin.

Veuillez noter que si vous changer de magasin, les prix affichés sur le site Web peuvent changer et votre panier d'achats pourrait alors se vider.

Conserver mon magasin Changer de magasin